PLUMBING BASICS: YOUR KEY TO BATHTUB INSTALLATION

Plumbing Basics: Your Key to Bathtub Installation

Plumbing Basics: Your Key to Bathtub Installation

Blog Article

Book

What're your ideas with regards to A Step-by-Step Guide to Installing a Bathtub?


Installing A Bathtub
Setting up a bath tub isn't precisely brain surgery, but it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard project. If the old bathtub is conveniently available, the task can move rapidly; if you need to open up a wall to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either case, the task is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the task and also fit attempting it. Rather than employing a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Chances are you may require a professional plumber to make tube links.
This post will aid you set up a brand-new tub in your restroom if you have actually already purchased a new bathtub and do not require to transform the arrangement of your previous water system pipelines.
Your devices and material checklist must make up the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome because of the restricted access that is frequently the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will come from the pipes. Once the supply pipes have been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
    Prior to going on to fit the new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
    If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next, position the faucet in the installing opening in the bath/basin making certain that the washers remain in place between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type should be attached to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.

    Installing the Tub


    Utilizing the two wood boards under its feet, place the tub in the needed setting. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
    The next goal is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the tub up until the spirit level reviews degree.
    To mount taps, fit all-time low of the furthest adaptable faucet adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
    Turn on the water system and examine all joints as well as brand-new pipework for leakages as well as tighten them if necessary. Fill the bathtub and additionally check the overflow outlet and the regular electrical outlet for leaks.
    Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the bath tub should wait until the tub has been made use of a minimum of when as this will resolve it right into its final setting.

    Preparing for the Installation


    First of all, the sustaining framework provided with the bathroom should be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
    Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its last position.

    Tiling Around the Bath tub


    In the location where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to split a stiff seal, causing the water to penetrate the wall surface between the bathroom and the tiling, resulting in issues with dampness as well as feasible leaks to the ceiling listed below.
    You can choose from a selection of coloured sealers to blend in your components and also installations. They are offered in tubes and cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to permit the motion experienced when the tub is in use. The sealant can crack rather very early if you do not consider this motion prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently readily available on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you enjoy reading up on A Step-by-Step Guide to Installing a Bathtub? Write feedback down the page. We would be delighted to listen to your views about this write up. In hopes that you come back again later on. Enjoyed reading our review? Please share it. Help another person discover it. We take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Clog issue? Reach out!

    Report this page